Posted Mon May 13, 2013, 10:10pm Subject: Brewtus III-R small mystery leak, lack of pressure regulator, or something else?
Hey guys, I looked under my Brewtus shortly after getting it setup and noticed this small accumulation. I also snapped some pictures inside, but I can't find the source (it's not happening fast enough for me to see any drips). I don't have a pressure regulator installed in the system yet, and WLL said not having one could cause the machine to leak from places (they said this without me mentioning my situation). I don't know what the water pressure is in my building, but I believe the machine doesn't drip if I turn it on with the water pressure shut off. I'd say the water may be concentrated near the solenoid in the center of the machine. Any other recommendations apart from getting a pressure regulator?
SStones Senior Member Joined: 24 Nov 2012 Posts: 510 Location: Canada Expertise: Professional
Espresso: Giga 5, ECM Giotto, Rocket... Grinder: Anfim Milano-Best Vac Pot: No :( Drip: Some $30 thing from Walmart Roaster: I buy pre-roasted.
Posted Tue May 14, 2013, 3:09am Subject: Re: Brewtus III-R small mystery leak, lack of pressure regulator
You're going to have to towel all the water up and spend some time just watching for the initial drop to find its source. You could either start with that, OR... Shut off the water, disconnect the supply and run the machine for a while with the hose in a pitcher, drawing water at a negative pressure to prove that the leak is not happening when the inlet isn't over-pressurized. And then sit with it watching for that tell-tale first drop.
Posted Fri May 24, 2013, 10:20pm Subject: Brewtus III-R small mystery leak, disassembly
Good idea! I've since been running water out of a container, but the leak remains slow yet persistent so tonight I finally got into the machine. Since experimenting with no line pressure, I've talked to WLL again who recommended I remove the T shaped connection with solenoid (see pic) for descaling and teflon taping. But while I'm at it, I'd like to be thorough and see what other people would do at this point.
What does the look of this scaled up boiler support/plug indicate? It almost looks like there's a burn mark on the fitting above it. Was planning to simply descale this and possibly teflon tape it. see pic
It only shows scale on one side, but it's pretty heavy. see pic see pic
Also there's quite a lot of scale around the top of the boiler see pic, and the boiler insulation itself seems like most of the material has condensed or dissolved.
Boilers are now drained, so I'm figuring I'll do a full machine descale when all goes back together, but first descaling and teflon taping the connections over the leak. I was never able to see a first drip, I'd just notice water pooling around the bracket that holds the solenoid, and also around where the boiler support meets the frame. Here's how the scale buildup on the frame looks with one boiler out. see pic
Posted Thu Jun 6, 2013, 12:36pm Subject: Brewtus III-R small mystery leak, lack of pressure regulator, or something else?
Just got this finally resolved and wanted to share an update in case anyone else ever runs into a hard to trace leak under the solenoid. WLL recommended the pressure regulator first, but after the above recommendation I tried drawing from a container with no line pressure, and still got the same slow leak. At that point, WLL recommended I remove the T connector and solenoid between the boilers, and clean/teflon tape everything. My suspicion was scale in the solenoid itself, which did turn out to be obviously present. Man, getting these parts out was a lot more complicated than I anticipated, because I had to remove the entire steam boiler and remove the brew boiler's plug/support from the base (because it looked like it might be leaking or drawing scale up from the base). It went back together a little harder than it came apart, and when I went to turn it on (heating elements disconnected due to empty boilers), it would flip the GFI. At first I thought I was getting poor ground due to dirty terminals or shorting somewhere in the wire, but what ended up solving my problem was compressing the connector a bit with a small flat head screwdriver, so it gripped the terminal more tightly.
Now the machine warms up as it should, and no leaks! But still not running a pressure regulator, as I've spent so much time and money on this machine that I feel like getting some return on that investment before messing with anything : ) From what I've read, lowering line pressure is most important for manual preinfusion. If there's any risk to pump seals, etc. Please let me know.
Symbols: = New Posts since your last visit = No New Posts since last visit = Newest post
Forum Rules: No profanity, illegal acts or personal attacks will be tolerated in these discussion boards. No commercial posting of any nature will be tolerated; only private sales by private individuals, in the "Buy and Sell" forum. No SEO style postings will be tolerated. SEO related posts will result in immediate ban from CoffeeGeek. No cross posting allowed - do not post your topic to more than one forum, nor repost a topic to the same forum. Who Can Read The Forum? Anyone can read posts in these discussion boards. Who Can Post New Topics? Any registered CoffeeGeek member can post new topics. Who Can Post Replies? Any registered CoffeeGeek member can post replies. Can Photos be posted? Anyone can post photos in their new topics or replies. Who can change or delete posts? Any CoffeeGeek member can edit their own posts. Only moderators can delete posts. Probationary Period: If you are a new signup for CoffeeGeek, you cannot promote, endorse, criticise or otherwise post an unsolicited endorsement for any company, product or service in your first five postings.