Posted Fri Oct 28, 2011, 8:38am Subject: Re: The Crossland CC1 Machine - CG Road Trip!! (Looking for a few good geeks)
Great idea Jon, I would have joined in the Road Show, but, I brought one home last night from Clive Coffee and it is heating up next to the GS3 in the kitchen at the moment (I need a machine to use at work, so I thought I would try it). I ran through the parameters to see what the default settings were, and I came on here to see if anyone had a temp offset listed as mine is set at 0. If I don't find it I'm going to give Bill C. a call to check all the parameters before I pull some shots through it. I also need to get a bottomless for it, so I can use it with the scace, as the standard two lug PF's won't fit the group.
Posted Fri Oct 28, 2011, 11:15am Subject: Re: The Crossland CC1 Machine - CG Road Trip!! (Looking for a few good geeks)
I'd be interested in partaking. I am a Rancilio Silvia owner, (with a P.I.D.) but not sure I am well enough versed in all the tech-speak. I am fascinated by the idea of such a simple platform for espresso. What is the price point for this machine? Is it for sale anywhere? Dying to read a review or comparison...
Just saw the CC1 for $699 at Seattle Coffee Gear. I wondered if this was being compared to a Sivia if it was in the same price range. Sweet deal with a P.I.D.
Holy cow, -8? I just ran a battery of tests...I do not have a bottomless PF for it yet, so I double checked the GS3 with the scace, then set up the styrofoam cup with a digital temp probe in it, I had a 10 degree difference with this method on the GS3, then tested back & forth to the CC1 letting both recover to their set point. When I spoke with Bill before my testing to confirm the correct offset, he stated the difference was built into the software, so the setting would reflect 0 in the set-up menu...so you are not seeing the boiler temp, but what is expected at the group, on the display.
My observation was the first two to three after a 15 minute idle was dropping about 2 degrees, climbing to the setpoint on the 3rd pull or so. Each time I just waited for the unit to "beep" then retest. I also have the delay after 1 second pre-infuse set to 6 sec, so I would start the procedure, dump the initial amount from the cup and get it back under the group @ the 6 second mark, then run for about 80ml of water (around the 15-16 sec mark). I did find a flash boil from the group on about the 6-7th (back to back) test on the machine. I think this must be pushing the limits of boiler recovery, causing some type of thermal overshoot, but, with actual usage times of more like 2 minutes, this didn't occur.
Don't mean to hijack the thread, but thought the info on the settings would be useful as the machine gets sent around and played with.
Symbols: = New Posts since your last visit = No New Posts since last visit = Newest post
Forum Rules: No profanity, illegal acts or personal attacks will be tolerated in these discussion boards. No commercial posting of any nature will be tolerated; only private sales by private individuals, in the "Buy and Sell" forum. No SEO style postings will be tolerated. SEO related posts will result in immediate ban from CoffeeGeek. No cross posting allowed - do not post your topic to more than one forum, nor repost a topic to the same forum. Who Can Read The Forum? Anyone can read posts in these discussion boards. Who Can Post New Topics? Any registered CoffeeGeek member can post new topics. Who Can Post Replies? Any registered CoffeeGeek member can post replies. Can Photos be posted? Anyone can post photos in their new topics or replies. Who can change or delete posts? Any CoffeeGeek member can edit their own posts. Only moderators can delete posts. Probationary Period: If you are a new signup for CoffeeGeek, you cannot promote, endorse, criticise or otherwise post an unsolicited endorsement for any company, product or service in your first five postings.