Posted Tue May 15, 2012, 4:41pm Subject: Modifying Saeco Via Venezia (OPV, p. gauge, depres. PF, pressure profiling, etc)
Hey guys, so i recently got my Saeco Via Venezia from CL and i cant help but start modding it. I believe the Aroma and Starbucks Barista machine is pretty much the same thing, also(thinking adding these words will probably help for the search engine)
wsikes and i have been talking back and forth in his grinder thread and i figured that the information would be more useful in this forum in it's own thread.
Depressurizing the PF: So one of the first things i did so far is depressurize the portafilter. i know this has been described in detail many times before. It is extremely simple, just remove the three screws on the bottom of the PF and pop off the plastic mechanism inside with a flat head screwdriver then push out the rubber gasket. Clean up all the parts and reassemble without the gasket and plastic mech.
Pressure Gauge: Next, i heard that these machines come set running at about 11bar(for the ese pods) and i'd like to get it to 9bar. I have no way of measuring the pressure as of yet. I built a pressure gauge to attach to the steam wand where i'd open up the steam wand in brew mode and close off a release valve at the end of the gauge. The problem i have now is that the hose i have hooked up to the steam wand is too wide and wont seal well enough to hold in the pressure. I'm considering either replacing the steam wand with a gaggia wand or silvia wand as i hear they use a thicker wand and should fit properly with the 1/4" inner diameter hose i have. Otherwise, i'll need a smaller hose and a smaller barb to the gauge. I followed the instructions from this video to build it. Click Here (www.youtube.com) The other option is if you have the unpressurized portafilter from seattle coffee gear with the spout, i'm thinking something like this may work Click Here (www.espressotec.com)
Overpressure Valve(OPV): So from my searching around, everyone seems to say to just add an OPV from a different machine as these Saeco machines are not supposed to have an OPV. From my research, i found that there is a pressure release valve installed from the factory. This valve Click Here (www.espressocare.com) is installed. You can see it here on the left of the pump http://www.myschiffman.org/cg/CIMG0378-2.JPG (not my picture, credit goes to http://ulkapumprepair.blogspot.com/ ). I was curious why no one mentioned this valve in all the searching of information that i did and figured there must be something about this valve that wouldnt allow me to adjust pressure. So then i contacted Stefano at http://www.espressocare.com asking about the valve and if it is indeed adjustable and if not, what valve would be better. He informed me that the valve is indeed adjustable by screwing or unscrewing the barbed end(usually bottomed out by factory) but since there is no pressure gauge, it would be difficult to know what the adjustment would end up at.
another option for adjusting the pressure i found from Click Here (www.saecomods.com) by using a lamp dimmer to adjust the voltage going to the pump. it seems pretty simple and from what they are saying, it is pretty reliable and effective. I have a dimmer on order right now and may use it if manually adjusting doesnt work for me.
Posted Tue May 15, 2012, 5:58pm Subject: Re: Modifying my Saeco Via Venezia (OPV, pressure gauge, depressurized PF, etc)
Frank, I think the pressure relief valve is just a blow-off valve like the one on a hot water heater. If you set it to a lower pressure it will likely be activated by normal boiler pressure and blow steam and hot water off inside the machine.
Posted Tue May 15, 2012, 6:06pm Subject: Re: Modifying my Saeco Via Venezia (OPV, pressure gauge, depressurized PF, etc)
btw i just ordered a silvia v3 steam wand and will attempt to get it to fit. I should be able to remove the nozzle and attach the 1/4" tubing from the gauge onto it as long as it's a thicker wand and closer to the size of the gaggia's.
im hoping this will solve this problem AND give me a better steaming wand when i'm done. I might have to elevate the machine if the wand is too long, though.
Posted Tue May 15, 2012, 6:19pm Subject: Re: Modifying my Saeco Via Venezia (OPV, pressure gauge, depressurized PF, etc)
Good luck with the valve and the steam wand. I called Seattle Coffee Gear and the parts guys were gone for the day, but the lady on the phone assured that the steam wand you ordered will not fit my old style Aroma. I am going to have to open my machine up and look for a valve like you are talking about on your machine. If nothing else, I'll have to call Stephano myself after looking inside my machine. I don't drink milk drinks but I made a cappo for my non-coffeedrinking wife the other night and I'll have to say that the old steam wand seemed to do a pretty good job. Maybe it was beginner's luck. So much to think about right now, but enjoying my "fast-pulled" Americanos for the time being. Gotta get that dimmer switch installed this weekend.
Posted Tue May 15, 2012, 9:38pm Subject: Re: Modifying my Saeco Via Venezia (OPV, pressure gauge, depressurized PF, etc)
hey D4F, yeah i saw that one while i was searching for information on OPVs. Problem is that i dont know how i'd mount it AND the headache of finding the right connections/hoses to get it working.
i'm really hoping the factory valve will work out.
on a side note, i used to machine for the first time and got it dialed in in about 3-4 tries. not bad. used some intelli black cat and got it tasting somewhat close to the shot i got from them tonight. i noticed after the 2nd shot, i couldnt distinguish any of the flavors. damn espresso overload on my palate.
oh also, i have the naked portafilter coming from SCG in a day or two. That should be fun.
Symbols: = New Posts since your last visit = No New Posts since last visit = Newest post
Forum Rules: No profanity, illegal acts or personal attacks will be tolerated in these discussion boards. No commercial posting of any nature will be tolerated; only private sales by private individuals, in the "Buy and Sell" forum. No SEO style postings will be tolerated. SEO related posts will result in immediate ban from CoffeeGeek. No cross posting allowed - do not post your topic to more than one forum, nor repost a topic to the same forum. Who Can Read The Forum? Anyone can read posts in these discussion boards. Who Can Post New Topics? Any registered CoffeeGeek member can post new topics. Who Can Post Replies? Any registered CoffeeGeek member can post replies. Can Photos be posted? Anyone can post photos in their new topics or replies. Who can change or delete posts? Any CoffeeGeek member can edit their own posts. Only moderators can delete posts. Probationary Period: If you are a new signup for CoffeeGeek, you cannot promote, endorse, criticise or otherwise post an unsolicited endorsement for any company, product or service in your first five postings.