Posted Thu Mar 6, 2014, 7:37am Subject: Re: Remove the lower burr carrier from a Macap M4?
I've done this but it's a bit hard. Once you remove the M8 nut holding it down you need to wedge a flat head screw driver under it and pry it off. Give it a nudge or 2 up and down then rotate to bring it up leveled. That's it. It's a friction fit so it's a bit of a pain. Watch you don't bash your knuckles. I do it every time.
PS: Macap users. You may want to take this off from time to time. A lot of coffee grinds end up under this thing and a shop vac can't get to it.. Was gross the last time I did it.
When I first got my K-6 it had seen serious neglected duty in a coffee shop somewhere. There was thick rancid build up on everything. The only way to get it all clean was to disassemble and scrub- I found a green scrubby to be quite effective. So yes there are reasons one might have to remove the lower burr carrier.
Edit to add- what Burner said is true of a lot of grinders, mine is probably due to be pulled again.
donflick Senior Member Joined: 5 Mar 2014 Posts: 3 Location: Fort Collins, CO Expertise: Just starting
Posted Fri Mar 7, 2014, 2:07pm Subject: Re: Remove the lower burr carrier from a Macap M4?
Thanks everybody for the info so far. I tried the screwdriver approach (insert the screwdriver through the opening in the aluminum casting where the ground coffee exits, right?) Couldn't get it to budge. Got nervous about applying lopsided force. So I made a "puller" - piece of 1/4 inch plywood with three holes. Plywood goes across the top. 2 inch screws go through the plywood and into the threaded holes for the burr. Nice, controlled, straight up force on the carrier. Still nothing. Maybe I am being too careful, but I sure don't want to break anything. Maybe I didn't get the screwdriver approach right (didn't do anything that even remotely put my knuckles at risk).
Posted Fri Mar 7, 2014, 7:15pm Subject: Re: Remove the lower burr carrier from a Macap M4?
Agreed, especially if its been on a long time, it's going to require some force. Maybe more than your plywood will alow for. You did take the center nut off, correct? I'm assuming you did but you didn't actually say and I hate to assume!
Posted Mon Mar 10, 2014, 3:21pm Subject: Re: Remove the lower burr carrier from a Macap M4?
Thanks guys for the added info on this thread. I gave one of my M4s a thorough cleaning today. The lower carrier came out with too much difficultey. I took the plastic upper of the doser off first, so I could pry the carrier up through the exit chute. It wasn't nearly as disgusting as I was expecting based on your comments, but it was definitely needed...we'll see how my other M4 looks though!
. Always remember the most important thing is what ends up in your cup!
Symbols: = New Posts since your last visit = No New Posts since last visit = Newest post
Forum Rules: No profanity, illegal acts or personal attacks will be tolerated in these discussion boards. No commercial posting of any nature will be tolerated; only private sales by private individuals, in the "Buy and Sell" forum. No SEO style postings will be tolerated. SEO related posts will result in immediate ban from CoffeeGeek. No cross posting allowed - do not post your topic to more than one forum, nor repost a topic to the same forum. Who Can Read The Forum? Anyone can read posts in these discussion boards. Who Can Post New Topics? Any registered CoffeeGeek member can post new topics. Who Can Post Replies? Any registered CoffeeGeek member can post replies. Can Photos be posted? Anyone can post photos in their new topics or replies. Who can change or delete posts? Any CoffeeGeek member can edit their own posts. Only moderators can delete posts. Probationary Period: If you are a new signup for CoffeeGeek, you cannot promote, endorse, criticise or otherwise post an unsolicited endorsement for any company, product or service in your first five postings.