grimaldo Senior Member Joined: 4 Oct 2011 Posts: 18 Expertise: Just starting
Posted Tue Oct 4, 2011, 8:39am Subject: Nuova Simonelli MCD disassembly
I have a Nuova Simonelli MCD grinder and I am trying to take it apart to clean it. I have tried removing the 4 screws on top, thinking that would free the top for removal, but the top was still pretty secure with those screws removed. Does anyone here know what I need to do to completely loosen the top of this grinder so I can get at the burrs for cleaning?
jlhsupport Senior Member Joined: 22 Oct 2010 Posts: 85 Location: Lafayette, IN Expertise: Professional
Posted Mon Oct 10, 2011, 7:14am Subject: Re: Nuova Simonelli MCD disassembly
Since it is a stepless grinder, there really isn't a fixed set point that you can simply say, "Set the grinder to X and leave it there." Basically, all you have to do is reassemble the grinder after cleaning, with the grinder on adjust the mechanism until the burrs begin "chirping," and then quickly back it off a few turns. Then you should grind some beans and brew, so you can find the setting on the grinder that matches your espresso machine. If the espresso is gushing out or not coming out at all, just remember that a complete turn of the knob is a very small change--this way, you don't waste as much coffee when dialing it in.
banffcoffee Senior Member Joined: 26 Feb 2013 Posts: 1 Location: Alberta, Canada Expertise: Just starting
Posted Tue Feb 26, 2013, 12:02pm Subject: Re: Nuova Simonelli MCD disassembly
Hi there. First time poster so be patient! I have a MCD 65 RA which I'm trying to clean out for a friend. I've taken off the output spout and cleaned that out, as well as the top plate screws and adjustment knob taken off. I can't seem to get the top cover plate to disengage, although after looking at the parts diagram, I'm not sure if taking the top plate will assist at all in cleaning.
Also, is there a thermostatic fuse on this machine? My friend had indicated that the grinder was getting quite hot during frequent use, and I'm wondering if perhaps this could be related to a heat switch in the unit (or the capacitor?).
calblacksmith Moderator Joined: 25 Nov 2007 Posts: 7,312 Location: Riverside, Ca, U.S.A. Expertise: I live coffee
Espresso: ECM Veneziano A1 Grinder: Many different commercial Vac Pot: 40s era Silex Drip: Milita, Bunn&Curtis... Roaster: Cast iron pan, gas burner
Posted Tue Feb 26, 2013, 2:44pm Subject: Re: Nuova Simonelli MCD disassembly
It has been a few years since I took my MCD56 apart. I seem to remember the 4 screws and the adjustment knob but not much else. There is a sticker on the side of mine that says THERMIC ALARM or some such thing so there seems to be a sensor or over temp device installed.
The grinder should not be run non stop, there should be breaks in time to allow the grinder to cool. Most commercial grinders on a 2/10 cycle or close to that. Two minutes on then ten minutes cool down between cycles.
EDIT; I seem to remember something about the plastic collar needing to come off for access to something too. YMMV!
In real life, my name is Wayne P. Anything I post is personal opinion and is only worth as much as anyone else's personal opinion. YMMV!
Feed the newbs, starve the trolls and above all enjoy what you drink!
Symbols: = New Posts since your last visit = No New Posts since last visit = Newest post
Forum Rules: No profanity, illegal acts or personal attacks will be tolerated in these discussion boards. No commercial posting of any nature will be tolerated; only private sales by private individuals, in the "Buy and Sell" forum. No SEO style postings will be tolerated. SEO related posts will result in immediate ban from CoffeeGeek. No cross posting allowed - do not post your topic to more than one forum, nor repost a topic to the same forum. Who Can Read The Forum? Anyone can read posts in these discussion boards. Who Can Post New Topics? Any registered CoffeeGeek member can post new topics. Who Can Post Replies? Any registered CoffeeGeek member can post replies. Can Photos be posted? Anyone can post photos in their new topics or replies. Who can change or delete posts? Any CoffeeGeek member can edit their own posts. Only moderators can delete posts. Probationary Period: If you are a new signup for CoffeeGeek, you cannot promote, endorse, criticise or otherwise post an unsolicited endorsement for any company, product or service in your first five postings.