You may want to consider putting a sheet of plastic or something on the underside of the cabinet. I did that for a setup some years ago. Just a sheet of acrylic or thin plexiglas type of material. That kept steam from ruining the cabinet above it. One tip, pre-drill any holes you need for mounting it. Hard plastics like this don't expand and will crack if you just try to screw straight through them. I also put a bead of caulk between it and the cabinet. This largely eliminated the problems steam was causing.
I don't have to move ours to fill it. I got a sink faucet that has a hose built into it. I just pull out the spout and snake it over to the coffee machine. MUCH easier than dealing with filling the carafe.
For when I do have to move it (for cleaning and the like) I put the machine on a single piece of floor tile, which has some teflon furniture slider feet on the bottom of it. This way the tile just slides right out, machine and all. I used a piece of nice black marble. I find a black tile hides the inevitable crud a little longer...
Most tile places have single tiles as samples you can purchase, so pick something that works for your decor. I have to buy a slightly larger piece for the HT. With my previous machine I had it and the grinder on the same 12"x12" piece of tile. The HT is about an inch wider and now the grinder doesn't fit. I plan on picking up a longer piece and cutting it to size. I have a wet saw left over from remodeling the whole bathroom ($70 cheapie from Harbor Fright). But I'd imagine a tile shop could trim one down for you for a few bucks.
purpledew88 Senior Member Joined: 19 Jan 2011 Posts: 2 Location: Las Vegas Expertise: I like coffee
Posted Wed Jan 19, 2011, 11:33am Subject: Re: Bunn Phase Brew™ - New Bunn Brewer
I rec'd mine HG on Dec 1st. and it's stop working already. It read "Heating Water" and a moving "racetrack" graphic displayed but nothing happend. Rec'd the replacement unit yesterday and run a batch with water only to check out the spray heat. I see only 2 steady streams of water and the third one is dripping pattern. What's the deal with these new Bunn machine ?
Posted Thu Jan 20, 2011, 7:07pm Subject: Re: Bunn Phase Brew™ - New Bunn Brewer
mario57, I've been holding off on posting as I test my replacement HT, but...
I tend to agree with you, but (1) Bunn makes a point that you should get this "spray pattern" and (2) twice I've found patches of dry ground coffee in the filter after brewing a 30oz pot. If there is *dry* coffee in the basket, then there can't possibly be good extraction throughout, no? The basket only seems to fill with water when brewing a full 40oz pot. Perhaps I need to grind *really* fine?
I also get better "spray" results with a 40oz pot. I've never seen anything more than two streams and a drip with 30oz (for what that's worth). I can't imagine what a 20oz pot does in there. Perhaps I'll have to check.
wkearney99 Senior Member Joined: 8 Oct 2010 Posts: 35 Location: Bethesda, MD Expertise: I love coffee
Posted Thu Jan 20, 2011, 7:41pm Subject: Re: Bunn Phase Brew™ - New Bunn Brewer
I switched to a very fine grind. I always brew a full pot. I've had fully saturated grounds each time. I still get the feeling it's not getting quite as strong a brew as I'd like. I'm wondering if it's letting the water out of the basket too quickly. I hesitate to start making modifications but would a gold filter slow the process more than paper? Or just the opposite?
Posted Thu Jan 20, 2011, 8:38pm Subject: Re: Bunn Phase Brew™ - New Bunn Brewer
Do you mean a gold filter for Bunn basket or the zmeister mod (see above). I"m not sure it would be any slower. I was wondering about making the hole smaller too, but that might make 40oz overflow the basket! Not much room for error in full pot.
Posted Fri Jan 21, 2011, 6:41am Subject: Re: Bunn Phase Brew™ - New Bunn Brewer
wkearney99, You may give Bunn a call and see if they will send you a replacement filter basket. If they are willing to send you one for for free, then you're really not out anything if you do the cone filter mod. The only reason I went ahead and did it is because I was grinding quite a bit finer than with a cone filter, and was still getting a weak flavored cup. I do think that you will get better results with a gold-type filter. It won't slow the process, but should let more oils and fines through. Of course, the cost is you get a little bit of sludge at the bottom of the cup. Has anyone out there tried any other type of basket style paper filters besides Bunn brand?
Symbols: = New Posts since your last visit = No New Posts since last visit = Newest post
Forum Rules: No profanity, illegal acts or personal attacks will be tolerated in these discussion boards. No commercial posting of any nature will be tolerated; only private sales by private individuals, in the "Buy and Sell" forum. No SEO style postings will be tolerated. SEO related posts will result in immediate ban from CoffeeGeek. No cross posting allowed - do not post your topic to more than one forum, nor repost a topic to the same forum. Who Can Read The Forum? Anyone can read posts in these discussion boards. Who Can Post New Topics? Any registered CoffeeGeek member can post new topics. Who Can Post Replies? Any registered CoffeeGeek member can post replies. Can Photos be posted? Anyone can post photos in their new topics or replies. Who can change or delete posts? Any CoffeeGeek member can edit their own posts. Only moderators can delete posts. Probationary Period: If you are a new signup for CoffeeGeek, you cannot promote, endorse, criticise or otherwise post an unsolicited endorsement for any company, product or service in your first five postings.