Posted Sat Nov 12, 2005, 10:22am Subject: Re: Z&D Update
Thanks for the comments.
Sometime back while I was ordering a chaff screen or something from Lisa at Z&D I mentioned this string and recomended that she check it out. I think at the time I just had the thermocuple probe installed and the roaster leads coming out of the case. It was primitive, but it worked and the concept of a higher power roast heater and temp probe in the roast chamber were there. I don't know if she checked it out or not.
It could be that their liability lawyers saw it and went into spin-dry.
I believe that if they were to put a temperature probe into the roast chamber and replace the 400 watt roast heater with a 700 watt heater controlled with a phase control lamp dimmer, they would have a machine which Coffee Geeks would be lineing up to buy and it wouldn't cost them much.
Wow Phil those are some extensive mods! Have you considered sharing your ideas with Z&D for their someday next generation roaster?
Thanks a lot for sharing your ideas and hard work!
Posted Thu Jun 21, 2012, 12:57pm Subject: Re: Z&D Update
This is the latest update to my Z&D. Since I started with this thing I have been boosting the voltage to the roast heater to get a faster temperature vs. time ramp. With my variable transformer I can get to 150 volts which raises the power of the roast heater to ~ 625 Watts from the OEM 400 Watts. This of coarse has rendered the roast heater a consumable. Z&D and now Nesco would not hear of selling me roast heaters. I have been getting by through the generosity of CoffeeGeeks who have sold or given me their dead machine to harvest heaters from.
Since I was on my last OEM heater and it looked pretty decrepit I have been pushed into doing what I've been talking of since 2004. I have installed a more powerful heater into the machine.
The Doner nichrome coil came from the corn popper heater shown below:
Posted Thu Jun 21, 2012, 1:04pm Subject: Re: Z&D Update
The image below shows the "new" coil and the remains of an old OEM coil. Note the string inside the coil. I would like to know what the material is. I did untie it successfully but looking at it with little fibers dropping off I have to wonder if it should be used near something which I plan to ingest. I elected to not use it.
Posted Thu Jun 21, 2012, 1:34pm Subject: Re: Z&D Update
Since I elected to not use the questionable string the coils looked as they could expand and touch the mounting screws. I have used a three wire cord and grounded the exposed metal parts so there is no hazard except to the coffee in the even of the roast getting interrupted by a short. I crammed some mica sheet between the screws and the coil and secured it with RTV.
I am regarding this as a prototype as I want to get rid of the mica altogether. The mica does stand the heat however it does deteriorate.
Ultimately I want just Nichrome and ceramic but this will give me an idea how a high power heater controlled by a phase control dimmer works compared to the OEM heater powered via the variable transformer.
So far I think I am going to like it although I had to go easy on the heat to avoid smoke from the not fully cured RTV. One thing I did notice is that the EMI from the router controller effected the electronics in the machine as when I changed the power the speed of the motor would change. It is not a problem except when speed changes in a Z&D one worries that the auger bearing is about to seize.
Below is a picture of the variable transformer which I used with the old heater next to the Harbor Freight router controller which I now use.
Posted Mon Jun 25, 2012, 11:01pm Subject: Re: Z&D Update
So far I am liking this configuration. The RTV smoke has subsided so I can run it full power (~800 Watts). This is a bit more margin over the old configuration. I no longer have to worry about room ambient temperature. For the next iteration I may go for ~ 1000 Watts.
Posted Tue Jun 26, 2012, 1:53pm Subject: Re: Z&D Update
The new coil is mounted on the form of a failed roast heater.
I'd like that heater which you are showing in there. I have thought of extending the bottom of the machine and supporting the auger drive shaft on two bearings spaced farther from the roast heater and having room for a heater which you are showing.
What my next iteration will probably look like is a bunch of ceramic stand-offs mounted to the roast chamber metal and the heater supported on the standoffs with no mica. I am looking at the ceramic parts which you gave me.
I hope to have this completed before the present configuration fails.
You should be able to easily handle 500 gram loads with 1KW.
btw - That 'new coil' mica photo looks like the 'after-burner', not the heater, correct?
Symbols: = New Posts since your last visit = No New Posts since last visit = Newest post
Forum Rules: No profanity, illegal acts or personal attacks will be tolerated in these discussion boards. No commercial posting of any nature will be tolerated; only private sales by private individuals, in the "Buy and Sell" forum. No SEO style postings will be tolerated. SEO related posts will result in immediate ban from CoffeeGeek. No cross posting allowed - do not post your topic to more than one forum, nor repost a topic to the same forum. Who Can Read The Forum? Anyone can read posts in these discussion boards. Who Can Post New Topics? Any registered CoffeeGeek member can post new topics. Who Can Post Replies? Any registered CoffeeGeek member can post replies. Can Photos be posted? Anyone can post photos in their new topics or replies. Who can change or delete posts? Any CoffeeGeek member can edit their own posts. Only moderators can delete posts. Probationary Period: If you are a new signup for CoffeeGeek, you cannot promote, endorse, criticise or otherwise post an unsolicited endorsement for any company, product or service in your first five postings.